Baumatic B77BL Bedienungsanleitung

el 1AS26SS/B26SS/B40/ B70.1BL/B71TCBL/ B72BL/B72TCBL/W/ B77BL/B77TCBL/B78BL/ PHG602 Gas hobs

B70.1BL 10 Depth: 480 mm idth: 580 mm Width: 560 mm 2 x 1.75 kW semi-rapid burners urner Automatic ignition n stands o LPG conversion jet

B71TCBL 11 Depth: 480 mm idth: 580 mm Width: 560 mm 2 x 1.75 kW semi-rapid burners urner Flame failure safety device on each burner n stand

12B72BL Depth: 490 mm idth: 580 mm Width: 560 mm 2 x 1.75 kW semi-rapid burners rner Automatic ignition n stands o LPG conversion jets

B72TCBL/W 13 Depth: 490 mm idth: 580 mm Width: 560 mm 2 x 1.75 kW semi-rapid burners rner Flame failure safety device on each burner n sta

14B77BL Depth: 490 mm idth: 680 mm Width: 562 mm 2 x 1.75 kW semi-rapid burners rner Automatic ignition n stands o LPG conversion jets

B77TCBL 15 Depth: 490 mm idth: 680 mm Width: 562 mm 2 x 1.75 kW semi-rapid burners rner o Flame failure safety device on each burner n stan

16B78BL Depth: 490 mm idth: 680 mm Width: 562 mm 2 x 1.75 kW semi-rapid burners rner RANA cast iron pan stands lass with bevelled front ed

17HG60 Depth: 490 mm idth: 580 mm Width: 560 mm 2 x 1.75 kW semi-rapid burners rner re safety device on each burner RANA cast iron pan stand

Electrical details 18Rated Voltage: t with ax Rated Inputs: 0.008 to 0.02 kW (depending on model) ains Supply Lead: 3 core x 0.75mm² (Type RR-F &

B40 19 3.00 kW rapid burner urner = Control panel 70.1BL/B71TCB72BL/B72TCBL/ A = 3.50 kW wok burner B =C = 1.75 kW semi-rapid bD B

User Manual for your Baumatic AS26SS 90 cm 4 Burner gas glass hob with thermocouples B26SS 90 cm 4 Burner gas glass hob with thermocouples B40 Circul

2077BL/B77TCBL/hob B B78BL Using the gas Before MPORTANT: You should clean the hob surface (see “Cleaning and maintenance” section).

21he control knob will indicate which gas burner it operates. utomatic ignition (B70.1BL, B72BL, B77BL) aximum position. aximum and minimum setting s

22r failure, the burners can be lit by carefully using a match. Energy saving tips No In case of powePA S BURNERS Minimum diametre M daximumiame

Cleaning be disconnected from your ply before commencing any cleaning ne deposits whilst the sure that the hob surface, rts and hob burners have al

24 not blocked. eassemble the burners in the original way. o Wipe the pan stands over with a soft, damp cloth that has been ng out after being take

25irature rise of 85°C above the ambient temperature of the room it is located in, during n, a kitchen diner or a bed sitting room. IMPORTANT: The ap

26und the appliance and between the hob surface and any combustible materials. he appliance please check that the following items e packaging: 1 x Ba

B70.1BL B71TCBL 27W HG602 L 78BL onds with the relevant drawing for your hob on pages 26 - 27. B72BL B72TCBL/P B77BL B77TCBB

o IMPORTANT: You must have a gap of at least 25 mm between the underneath of the appliance and any surface that is below it. o Carefully tu

o Carefully turn the hob back over and then gently lower it into the aperture hole that you have cut out. o On the underneath of the hob, adjust th

3Contents Environmental note 4 Important safety information 5 – 7 Specifications 8 – 20 AS26SS/B26SS 8 B40 9 B70.

30o If the room has a volume of less than 5m³, it will require an air vent of 100cm² (effective area). o If it is installed in a room with a volum

o Put the gas seal into the elbow. o Fully tighten the elbow and seal onto the gas rail. o The elbow MUST be pointing in a downwards d

A = Gas inlet B = Seals C = Gas Elbow D = Copper pipe (not supplied) o Put the gas seal into the elbow. o Fully tighten the elbow and

o Unscrew the injector (B) and replace it with the stipulated injector for the new gas supply (see table below). GENERAL INJECTORS TABLE Pow

Minimum flow adjustment for hob gas taps. All work must be carried out by a GASSAFE registered engineer. IMPORTANT: Always isolate the hob from the

Gas tap maintenance These maintenance operations MUST ONLY be carried out by a GASSAFE registered engineer. IMPORTANT: Before carrying out any maint

o Reconnect the gas tap, perform a gas soundness test and then reassemble the hob. Electrical connection This appliance must be installed by a qual

My appliance isn’t working correctly IMPORTANT: If your appliance appears not to be operating correctly, then you should disconnect it from your main

Czech Republic United Kingdom Baumatic CR spol s.r.o. Baumatic Ltd., Průmyslová zóna Sever 696 Baumatic Buildings, 460 11 Liberec 11 6 Bennet R

39

Environmental note 4 o The packaging materials that Baumatic uses are environmentally friendly and can be recycled. all packaging mat

40

5Important safety information Your safety is of the utmost importance to Baumatic. Please make sure that you read this instruction booklet before at

6hild Safety ce at any time. During and after use, all surfaces will be hot. se ensure that they are kept under close supervision at all times. uld

7leaning Cleaning of the hob should be carried out on a regular basis. appliance, it should be disconnected from the mains and cool. using this ap

8pecifications S AS26SS/B26SS Product dimensions: Aperture dimensions: Height: 350 mm Height: 335 mm Width: 880 mm Width: 865 mm rs on eac

940 idth: 520 mm Width: 500 mm burner o 1 x 3.00 kW rapid burner burner Flame failure safety device on each burner o IMPORTANT: Not suitable f