BTC6720BL/SS, F60.2BL/SS, F70.2BL/SS, F90.2BL/SS, F100.2BL/SS Cooker hood
F70.2BL/SS PRODUCT DIMENSIONS Height: 700* mm – 1080 mm Width: 700 mm Depth: 500 mm DIMENSIONS OF CHIMNEY SECTION: 165 mm x 222 mm Your st
F90.2BL/SS PRODUCT DIMENSIONS Height: 700* mm – 1080 mm Width: 900 mm Depth: 500 mm DIMENSIONS OF CHIMNEY SECTION: 170 mm x 221 mm Your stai
F100.2BL/SS PRODUCT DIMENSIONS Height: 700 mm* – 1080 mm Width: 1000 mm Depth: 500 mm DIMENSIONS OF CHIMNEY SECTION: 170 mm x 221 mm Your st
Optional extras (all models) DK5 1 Metre length Ducting Kit 125 mm Ø. DK10 3 Metre length Ducting Kit 125 mm Ø with flat channelling included. o A
o Before operating the hood, make sure that it has been installed by a suitably qualified person, as per the information contained in Baumatic’s inst
The grease filters o Your cooker hood is fitted with grease filters, which help to absorb grease particles and protect your kitchen & furniture
o Refit the grease filters once they have dried. o IMPORTANT: Let the grease filters dry thoroughly before refitting them in the cooker h
o IMPORTANT: Defective bulbs should be replaced immediately. o If the lights still do not work, make sure that the lamps are fitted properly into t
o Repeat this process for the second carbon filter. You need to place a carbon filter at either end of the motor. o Refit the grease filters. o T
o Repeat this process for the second carbon filter. You need to place a carbon filter at either end of the motor. o Refit the grease filters. o T
User Manual for your Baumatic BTC6720BL/SS/W, F60.2BL/SS 60 cm cooker hood F70.2BL/SS 70 cm cooker hood F90.2BL/SS 90 cm cooker hood F100.2BL/SS 100
We recommend that the appliance is connected by a qualified electrician, who is a member of the N.I.C.E.I.C. and who will comply with the I.E.E. and l
o Select a flat surface for assembling the cooker hood. Cover that surface with a protective covering and place all cooker hood parts and fittings on
2a) The support screw holes are indicated by figure A in this drawing and the anchoring screw holes are indicated by figure B. 22 3) Usin
6) Hang the hood onto the support screws. 7) Fully tighten the support screws (A) and then screw the anchoring screws (B) through the
Connecting to external ducting 8) Connect the coupling to the top of the cooker hood, and then connect a 125 mm ducting hose to the coupling (please
10) Lift chimney section (D) upwards until it reaches the ceiling. You must ensure that it is perpendicular to the hood. o Mark the
12) Using a 6 mm drill bit, drill out two holes on the pencil markings that you made in step 11. Insert rawl plugs into the holes and
Completing the installation o If you are setting the appliance to recirculation mode, then you should now fit the two carbon filters. See the “Fitti
Troubleshooting IMPORTANT: If your cooker hood appears not to be operating properly, before contacting the Baumatic Customer Care Department, please
IMPORTANT: If your appliance appears not to be operating correctly, then you should disconnect it from your mains supply and then contact Baumatic Cus
3Contents Page Environmental note 4 IMPORTANT SAFETY INFORMATION 5 – 7 Specifications of your cooker hood 8 – 13 BTC6720BL/SS/
30 United Kingdom Czech Republic Baumatic Ltd., Baumatic CR spol s.r.o. Baumatic Buildings, Průmyslová zóna Sever 696 6 Bennet Road, 460 11
31
32
ENVIRONMENTAL NOTE Note: Before discarding an old appliance, switch off and disconnect it from the power supply. Cut off and render any plug useles
IMPORTANT SAFETY INFORMATION Your safety is of the utmost importance to Baumatic. Please make sure that you read this instruction booklet before att
o The edges of the cooker hood are sharp – be mindful of this as you handle your appliance, especially during installation and cleaning. DO NOT CLEAN
o Remember that when in extraction mode, your cooker hood is removing air from your room. Ensure that proper ventilation measures are being observed
Specifications of your cooker hood BTC6720BL/SS/W PRODUCT DIMENSIONS Height: 645* mm – 1025 mm Width: 600 mm Depth: 500 mm DIMENSIONS OF CHIMNE
F60.2BL/SS PRODUCT DIMENSIONS Height: 700* mm – 1080 mm Width: 600 mm Depth: 500 mm DIMENSIONS OF CHIMNEY SECTION: 170 mm x 221 mm Your stai
Kommentare zu diesen Handbüchern